Reclaimed wood - Queen size headboard

This is my first project that I designed myself! I had a general idea of the plan from one on Ana's site, but when I was trying to purchase reclaimed wood, the 1x6 @ 4ft were a better bang for my buck. The variation in the wood is just gorgeous, I'm obsessed! This project cost me about $120.

10 - 1x6 @ 4ft - cut to whatever size you choose
1x3 & 1x2 for supports & trim

For the finish I painted 2 of the panels with white spray paint & then distressed with my sander so some of the wood grain would show through. I stained 2 other panels with "sunbleached" see below. For the rest of the panels I left them in their natural beauty! The supports & trim pieces were brand new (whitewood), so I stained them with the "dark walnut".

Since I am an Army Wife & we move a lot I wanted to make sure that this piece of furniture would hold up to the beating it is going to get. In the pic to the left you can see where I placed my poket holes & that I placed the back supports in the same place that I placed the front trim pieces. When working with recliamed wood, don't force the wood to connect. Leave some of the gaps alone, you don't want to ruin the project & cause the wood to split even more.

For the legs I used a 1x3 & then attached a 1x2 on top of that with wood glue & counter-sunk screws. Fill in holes with wood filler! Put your horizontal trim pieces on the front, last. Measure each piece, because this wood was reclaimed & some pieces were split so the top & bottom pieces didn't end up being the same length.

 

 

 

DIY - Rustic Serving Tray

I made this easy project using a left over piece of 1x12 from another project! I decided to make it 18" long. For the sides I used 1x3. Measure each side & cut at 45 degrees off square. For added support, I attached the sides with PH screws from the bottom/underneath using my Kreg Jig & wood glue! To connect the 4 corners - I used wood glue & 1 1/4" finish nails.  Use your power sander to distress the paint if you like the way mine looks; I say - embrace the flaws in your wood! Last, add the poly/top coat with a foam brush for added durability.

Work Bench #2

My original work bench was my very first build; so it was not level. I must admit I had yet to purchase my counter-sinking drill bit & had not figured out how to use my Kreg Jig either! It is going to be used for storage now. I am proud to say build #2 is level! I would recommend changing the height of the legs to 30" for this plan to compensate for the height wheels. To see the build plans for this work bench click here or you can also search for it on Ana's website!

My compound miter saw is going to be so happy on the top of this baby, rolling smoothly around the garage! :)

 Happy Building!
~B

Triple Truss Coffee Table with Casters!

You too can turn this...

Into this:

For the plans on how to make this huge coffee table go to Ana White's site!
 I used my Kreg Jig to build this guy!

For the slats on the bottom measure from the end point of the 2x4 not the part where it is connected. I also drew little stars so I wouldn't get confused:

I would recommend sanding, staining & putting the poly on the base before attaching the top planks. There are a lot of angles that would be more difficult to get to if you wait until it is completely built.

For my casters: I chose these industrial beauties! They will rust though, so I would not use these if you are making this table for outside! My regular wood screws weren't wide enough for the casters holes, so I used my 1 1/4" PH screws to attach them to the bottom.

To see my brag on Ana's site click here!
Here are some more pictures! My stain color of choice: Dark Walnut. I added some industrial corner brackets to the top 4 corners as well! They match my wheels!

Thanks for stopping by!
B